Solution Description
Flange Mounted Planar Double Enveloping Worm Gear Device
Working conditions
Two shafts for 90 ° Intersect, enter speed must not be much more than 1500 rpm.The working environment temperature should range from 0 ~ 40 ° C, when the setting temperature underneath ° C or over 40 ° C.Just before starting up the lubricating oil to corresponding heating and cooling, The worm shafts, reverse procedure can be positive.
Knowledge sheet on CUW double enveloping CZPT reducer :
| Model | ShaftDia. (mm) | Center Height (CUW) | (CUW) Output shaft Dia. | Electrical power | Ratio | Permitted Torque | Bodyweight |
| (CUW) input Solid(h6) | (mm) | (mm) | (kw) | (Nm) | (KGS) | ||
| one hundred | 28 | one hundred ninety | forty eight | 1.forty one~eleven.five | 10 .twenty five~ 62 | 683-1094 | forty two |
| 125 | 32 | 225 | fifty five | 2.forty two~19.7 | 10 .25 ~ 62 | 1170~2221 | 65 |
| 140 | 38 | 255 | 65 | three.94~twenty five.9 | 10 .25 ~ 62 | 1555 ~ 3473 | 85 |
| a hundred and sixty | 42 | 290 | 70 | four.39~35.7 | 10 .25 ~ 62 | 2143 ~4212 | a hundred and twenty |
| one hundred eighty | forty eight | 320 | eighty | five.83~forty seven.five | 10 .25 ~ 62 | 2812 ~ 5387 | a hundred and seventy |
| 200 | fifty five | 350 | ninety | 7.52 ~sixty one.two | 10 .25 ~ 62 | 3624 ~6859 | 220 |
| 225 | sixty | 390 | one hundred | 9.9~81.4 | 10 .25 ~ 62 | 4872 ~ 9224 | 290 |
| 250 | 65 | 430 | 110 | twelve.9 ~one hundred and five | 10 .25~ 62 | 6284~11892 | 380 |
| 280 | 70 | 480 | one hundred twenty | sixteen.9 ~ 138 | 10 .25 ~ 62 | 8347 ~ 15820 | 520 |
| 315 | 75 | 530 | a hundred and forty | 22.5 ~183 | 10 .25 ~ 62 | 11068~ 19450 | seven hundred |
| 355 | eighty | 595 | a hundred and fifty | thirty~245 | 10 .25 ~ 62 | 14818 ~28014 | 1030 |
| 400 | ninety | 660 | a hundred and seventy | 32.1 ~261 | 10 .25 ~ 62 | 15786~29918 | 1400 |
| 450 | a hundred | 740 | a hundred ninety | 42.6 ~347 | 10 .25 ~ 62 | 2571~39881 | 1980 |
| five hundred | 110 | 815 | 210 | fifty four.9 ~ 448 | 10 .25 ~ 62 | 27097~51180 | 2700 |
The tooth surface hardness, it is divided into soft tooth surface equipment transmission and challenging tooth floor gear transmission. When the tooth surface area hardness of the two wheels (or a single of them) is significantly less than or equivalent to 350HBW, it is known as delicate tooth area transmission when the tooth floor hardness of the two wheels is >350HBW, it is named difficult tooth floor transmission. Delicate-tooth surface area gear transmission is often utilised for standard low-pace equipment transmission that does not need higher precision, and difficult-toothed floor equipment transmission is often employed for gear transmission that calls for robust bearing ability and compact construction.